KATOOL · SKU: KT-4H120X
Katool 4-Post Alignment Lift - 12,000lb Capacity. Rolling Jack Included | KT-4H120X
In Stock
Technical Specifications
| SKU | KT-4H120X |
| Brand | KATOOL |
| Category | 4-Post Lift |
| Lift Capacity | 9,000 lbs |
| Configuration | Symmetric |
| Maximum Lifting Height | 72 inches |
| Minimum Ceiling Height | 11 feet |
| Overall Width | 140 inches |
| Overall Height | 140 inches |
| Front Arm Design | 3-stage telescoping with rubber pad adapters |
| Rear Arm Design | 2-stage telescoping with rubber pad adapters |
| Power Requirements | 220V, 60Hz, single-phase |
| Motor Power | 2.2 HP |
| Safety Features | Single-point safety lock release, overhead safety shut-off bar |
| Lifting Time | 50 seconds (floor to full height) |
| Certifications | ALI/ETL Certified |
| Warranty | 1-year parts, lifetime structural |
| Shipping Weight | 1,180 lbs |
| Country of Origin | China (manufactured to North American standards) |
Need a Service-Ready Alignment Lift? Step Up to the Katool KT-4H120X 12,000 lb 4-Post Lift with RJ70 Rolling Jack
Buying a 4-post alignment lift sounds straightforward until the real questions start stacking up. How stable is it under a 10,000 lb truck? Does the lifting height actually give you enough room to work underneath? And what about wheels-off service -- do you need to buy a rolling jack separately, or does the package actually come ready to work? A lot of lifts look similar in photos, but once you're using one daily, the gaps show up fast. The KT-4H120X by Katool is built to close those gaps -- a true 12,000 lb rated capacity with an RJ70 7,000 lb pneumatic rolling jack included in the box, not sold as an add-on.
The safety system is where this lift separates from the pack. Mechanical locking devices on each column with primary and secondary lock-style backups, a single-point manual safety release, a top limit switch to prevent over-travel, and a quad cable synchronization system that keeps both platforms level through every inch of travel. Max lifting height is 86.9 inches with 80 inches of underneath clearance, so you have real working room -- not just enough to squeeze under with a creeper. Lift cycle is 83 seconds up and 40 seconds down on 220V single-phase power, which is the only voltage option on this model.
What makes the KT-4H120X a genuine alignment platform is the runway setup. Rear slip plates are built into the runways, and front alignment turn plates can be added separately to complete a four-wheel alignment configuration. The included RJ70 rolling jack lets you lift the axle or frame so wheels hang free for brake jobs, tire rotations, suspension work, and more -- all without moving the vehicle off the lift. Overall length with ramps is 258 inches, overall width is 135.2 inches, and post height is 94.88 inches, so measure your bay before ordering. If you need a 4-post lift that's genuinely built for daily service and alignment work out of the box, this is the one that delivers.
Need a different capacity or size? Explore our full lineup of Vehicle Lifts or call us at (470) 208-2754.
Benefits of the Katool KT-4H120X
Key Features of the Katool KT-4H120X 4-Post Lift You'll Love:
• 12,000 lb Drive-On Capacity: Rated for 12,000 lbs, giving you real breathing room for heavy SUVs, full-size trucks, and fleet vehicles that push lighter lifts to their limits. This isn't a lift you'll outgrow when you take on bigger jobs -- it's built to handle the vehicles most shops actually see every day.
• RJ70 7,000 lb Pneumatic Rolling Jack Included: This is the upgrade that turns a storage lift into a service platform. The RJ70 lets you lift the axle or frame so wheels hang free for brake jobs, tire rotations, suspension work, and more -- all without pulling the vehicle off the lift and onto a two-post. Most competitors sell the rolling jack separately. Here, it's in the crate.
• Alignment-Capable Runway Design: Rear slip plates are built directly into the runways, so you're already halfway to a full alignment setup out of the box. Front alignment turn plates can be purchased separately to complete a four-wheel configuration. This means you can start doing alignment work without buying an entirely separate alignment rack.
• 86.9" Max Lifting Height: Provides 80 inches of real underneath clearance when fully raised -- enough room to stand and work comfortably, not just slide under on a creeper. Whether you're doing exhaust work, transmission service, or full underbody inspections, you're not fighting for space.
• Multi-Layer Safety System: Mechanical locking devices on each column with primary and secondary lock-style backups, a single-point manual safety release, and a top limit switch. You're not relying on any single component to keep the vehicle in the air -- there's redundancy at every level.
• Free-Standing Design on 220V Power: Engineered for free-standing use without bolting to the floor. Runs on 220VAC/60Hz single-phase power, wired to a dedicated circuit with 10-gauge wire and a 30-amp breaker. No anchor bolts required for normal operation, though the concrete specs on this model are higher than smaller lifts -- 5.9 inches (150 mm) minimum thickness at 3,000 PSI.
Minimum Garage Requirements
✔ Ceiling Height: At least 100" (8'4") recommended ✔ Floor Space: 258" L x 136" W (21'6" x 11'4") ✔ Concrete Thickness: Minimum 5.9" (150 mm)
✔ Concrete Strength: Minimum 3,000 PSI compressive ✔ Electrical: 220V single-phase, 30A breaker, 10-gauge wire ✔ Post Height: 94.88" (7'11") -- measure before ordering
✔ Ceiling Height: At least 100" (8'4") recommended
✔ Floor Space: 258" L x 136" W (21'6" x 11'4")
✔ Concrete Thickness: Minimum 5.9" (150 mm)
✔ Concrete Strength: Minimum 3,000 PSI compressive
✔ Electrical: 220V single-phase, 30A breaker, 10-gauge wire
✔ Post Height: 94.88" (7'11") -- measure before ordering
*This lift is designed for free-standing use and does not require bolting to the ground for normal operation. Regardless of whether the lift is anchored, it must be installed on a concrete surface that meets the manufacturer's minimum requirements of at least 5.9" (150 mm) thickness and 3,000 PSI compressive strength. Installing this lift on inadequate concrete may result in serious injury or death. It is the customer's responsibility to verify concrete thickness and strength prior to purchase and installation.
| Katool KT-4H120X 12,000 lb 4-Post Alignment Lift Specifications | |
| Manufacturer | Katool |
| Model | KT-4H120X |
| Product Type | 4-Post Alignment Lift |
| Lifting Capacity | 12,000 lbs |
| Max. Lifting Height | 86.9" (2,208 mm) |
| Max. Underneath Clearance | 80" (2,032 mm) |
| Lifting Time | 83 seconds up / 40 seconds down |
| Height of Posts | 94.88" (2,410 mm) |
| Width Overall | 135.2" (3,435 mm) |
| Width Inside Columns | 112.81" (2,865 mm) |
| Width Inside Runways | 37" (940 mm) |
| Width of Runways | 20" (508 mm) |
| Length Overall (with ramps) | 258" (6,553 mm) |
| Runway Length | 205" (5,207 mm) |
| Runway Features | Rear slip plates integrated; front turn plates sold separately |
| Safety System | Mechanical locks with primary/secondary backups, single-point manual release, top limit switch |
| Synchronization | Quad steel cable & pulley system for level lifting |
| Included Accessory | RJ70 7,000 lb Pneumatic Rolling Jack |
| Motor | 220VAC/60Hz/1PH |
| Electrical Requirements | Dedicated circuit, 10-gauge wire, 30-amp breaker (220V only) |
| Concrete Requirement | 5.9" (150 mm) minimum @ 3,000 PSI |
| Net Weight | 3,373 lbs (1,530 kg) |
| Warranty | 1 Year limited parts & defects | 3 Year structural |
Ready to upgrade your garage? Talk to a Lift Specialist or explore more options.
Built for the serious home garage enthusiast and light commercial shop, the Atlas Garage Pro delivers professional-grade lifting performance at an accessible price point. This 9,000 lb capacity symmetric two-post lift is engineered with precision-machined components and industrial-grade hydraulics that ensure decades of reliable service.
The symmetric arm configuration provides optimal weight distribution for most passenger vehicles, light trucks, and SUVs. Three-stage telescoping front arms and two-stage rear arms give you maximum reach flexibility, while the included rubber pad adapters protect vehicle frame rails and pinch welds from damage during lifting operations.
Safety is paramount in professional lifting equipment. The Atlas Garage Pro features a single-point safety lock release system that allows for controlled, gradual lowering — eliminating the risk of sudden drops. The overhead safety shut-off bar provides automatic power cutoff if the lift reaches maximum height, preventing over-extension damage to the hydraulic system.
Installation requires a minimum 11-foot ceiling height and adequate floor reinforcement (4-inch minimum concrete thickness recommended). The lift operates on standard 220V single-phase power, making it compatible with most residential and commercial electrical systems without requiring costly three-phase upgrades.
Each Atlas Garage Pro ships with all necessary installation hardware, detailed assembly instructions, and access to our technical support team. Professional installation is recommended to ensure proper anchoring and safety compliance.
You May Also Like
